The rules come from two places. The California Green Building Standards Code, known as CalGreen, sets the maximum flow rates for new fixtures. And Senate Bill 407, written into California Civil Code sections 1101.1 to 1101.8, forces older homes to catch up. Together they mean that any fixture you buy in California today must meet the numbers in the table below — and that a remodel in an older home can trigger a whole-house fixture upgrade you did not budget for.
The Numbers California Requires
Every fixture sold in California must meet these maximums. The figures are stamped on the fixture or its packaging, and they are the first thing to check before you buy.
| Fixture | Old, non-compliant level | Current standard for new fixtures |
|---|---|---|
| Toilet | More than 1.6 gallons per flush | 1.28 gallons per flush maximum |
| Showerhead | More than 2.5 gallons per minute | 1.8 gallons per minute maximum at 80 psi |
| Bathroom faucet | More than 2.2 gallons per minute | 1.2 gallons per minute maximum at 60 psi |
| Kitchen faucet | More than 2.2 gallons per minute | 1.8 gallons per minute maximum at 60 psi |
A few details matter. For showers with more than one head on a single valve, the combined flow of all heads must not exceed 1.8 gallons per minute — you cannot fit two 1.8 gallon heads on one valve and call it compliant. Kitchen faucets are allowed a short temporary boost to 2.2 gallons per minute under the current code, for example when filling a pot, but the standard flow is 1.8. And the limits apply to what is sold and installed, not to what is already in your walls: an old 3.5 gallon toilet sitting in your bathroom does not have to come out tomorrow, unless a permit or a sale triggers the replacement rules below.
If you are replacing fixtures as part of a bathroom or kitchen project, our fixture installation page covers what a professional installation includes and what to check before the work starts.
SB 407 and Your Pre-1994 Home
This is the rule that catches homeowners by surprise. Senate Bill 407 applies to homes built and available for use on or before 1 January 1994. The law required owners of those homes to replace all non-compliant plumbing fixtures — toilets using more than 1.6 gallons per flush, showerheads flowing more than 2.5 gallons per minute, and indoor faucets flowing more than 2.2 gallons per minute — by 1 January 2017. Sellers must also disclose in writing whether any non-compliant fixtures remain.
The part that still bites today is the permit trigger. If you pull a permit for an alteration or improvement to a pre-1994 single-family home, the city will not give final approval until every remaining non-compliant fixture in the whole house has been replaced with water-conserving models. That means a bathroom remodel can turn into a whole-house fixture swap: the new bathroom gets compliant fixtures, and so does every other toilet, shower and tap in the house. It is not a huge cost in itself — a handful of fixtures and a day of work — but it is a cost that belongs in the budget before the project starts, not discovered at final inspection.
Two practical consequences follow. First, if you are buying a pre-1994 home, check the fixture disclosure carefully and look at the toilets yourself: the flush volume is usually stamped inside the tank or on the bowl. Second, if you are planning any permitted work on an older home, count the fixtures in the whole house and price the swap in advance. Finding out at final inspection means delays, a second inspection fee, and a rushed fixture choice.
Toilets: Where the Biggest Saving Sits
The toilet is the single largest indoor water user in most homes, and it is where the oldest fixtures waste the most. A pre-1994 toilet uses 3.5 gallons per flush or more. A 1994-era toilet uses 1.6. A current California-compliant toilet uses 1.28 gallons or less. For a household of four, each person flushing five times a day, the difference between a 3.5 gallon toilet and a 1.28 gallon model is thousands of gallons a year.
The United States Environmental Protection Agency estimates that swapping an old, inefficient toilet for a WaterSense-labelled model saves a typical household nearly 13,000 gallons of water a year. That figure is worth pausing on: it is the saving from one fixture, in one bathroom, with no change in behaviour at all.
The worry most people have is the flush itself. Early low-flow toilets from the 1990s earned a poor reputation — weak flushes, double flushing, clogged bowls — and that reputation has stuck around long after the products improved. Modern 1.28 gallon toilets are a different product. Here is what to look for:
- Flush performance rating. Look for a Maximum Performance (MaP) rating of 600 grams or higher. MaP testing measures how much solid waste a toilet clears in a single flush, and 600 grams is a practical benchmark for a family home.
- Trapway size and glazing. A fully glazed trapway — the passage waste travels through — reduces friction and clogging. A 2 inch or larger trapway clears waste more reliably than a narrow one.
- Gravity vs pressure-assisted. Gravity toilets are quieter and simpler, and they suit most homes. Pressure-assisted models flush harder and are a good choice for a busy family bathroom, but they are louder and the pressure tank is a part that will eventually need replacing.
- Rough-in measurement. Measure from the finished wall to the centre of the floor bolts before you order. Most California homes use a 12 inch rough-in, but older homes sometimes use 10 or 14 inches, and ordering the wrong one means a return trip.
- Comfort height. A bowl height of 17 to 19 inches suits most adults and is easier for older family members. Standard height is around 15 inches.
A dual-flush toilet, with a light flush for liquid waste and a full flush for solid waste, can save a little more water, but only if the household actually uses the light flush. In a rental or a busy family bathroom, a well-chosen single-flush 1.28 gallon model often saves more in practice, because nobody has to remember which button to press.
Showerheads: 1.8 Gallons Without a Weak Shower
The showerhead is where the law and the shopping experience collide. California caps every showerhead sold in the state at 1.8 gallons per minute, enforced through the California Energy Commission's appliance efficiency regulations under Title 20. That limit took full effect on 1 January 2018. It covers wall-mounted heads, handheld models and body sprays alike, and every showerhead legally sold in California must be listed in the Commission's appliance database.
The trap is online shopping. A showerhead rated at 1.9 or 2.0 gallons per minute meets the federal standard and even carries the WaterSense label, but it violates California law. If you order one from out of state, you may receive a product that cannot legally be sold here — and if it is installed during a permitted remodel, it will fail inspection. Always check the flow number on the packaging or the product specification sheet before you buy, and look for the number stamped on the unit itself.
A 1.8 gallon showerhead does not have to feel weak. The better ones use air-induction or pressure-compensating designs that mix air into the stream, so the spray feels fuller than the flow rate suggests. What to check in the shop:
- Spray pattern. A wide, even pattern with no dead spots matters more than the flow number. A head that concentrates the spray into a narrow jet feels harsh at any flow rate.
- Handheld plus fixed combinations. If a shower has both a fixed head and a handheld on the same valve, their combined flow must stay under 1.8 gallons per minute. Some manufacturers sell paired sets designed for exactly this; others do not, and the pairing is on you.
- Limescale. Much of Southern California has hard water, and a showerhead with silicone nozzles that you can rub clean with a fingertip will outlast one with fixed metal jets that slowly clog with mineral deposits.
- Height and angle. A head mounted too low or angled badly wastes water no matter how efficient it is, because the user stands half outside the spray. An adjustable arm is a cheap fix.
A low-flow showerhead also saves hot water, which means it saves the energy used to heat that water too. That is a double saving on the utility bill, and it is one reason a showerhead swap is the highest-return water-efficiency upgrade in most homes.
Faucets and Aerators: The Cheapest Upgrade in the House
Bathroom faucets in California are limited to 1.2 gallons per minute, and kitchen faucets to 1.8. But the cheapest water-saving upgrade in any home is not a new faucet at all — it is a new aerator. An aerator is the small mesh fitting screwed onto the end of the tap, and it controls the flow. A 1.0 or 1.2 gallon-per-minute aerator for a bathroom tap costs a few dollars, takes two minutes to fit with no tools beyond a pair of pliers and a cloth, and can cut that tap's water use nearly in half.
For the kitchen, a 1.5 gallon-per-minute aerator is a practical compromise: it keeps enough flow to fill a pot or rinse a pan without waiting, while still saving water on the everyday hand-washing and rinsing that makes up most kitchen tap use. If the tap has a pull-down sprayer, check the flow rate of the sprayer as well as the main stream — some sprayers bypass the aerator entirely.
When you do replace a faucet, the details that matter are unglamorous: a ceramic disc cartridge rather than a compression washer, because it lasts years longer without dripping; a solid brass body rather than a thin zinc casting; and a brand your local supply house stocks parts for, so a worn cartridge in five years is a ten-dollar part rather than a new faucet. A dripping tap wastes far more water than a slightly higher flow rate ever will, so build quality beats the headline number. If a tap has started dripping, our fixture installation team can usually fix a worn cartridge quickly.
What a Fixture Swap Actually Saves
These figures are estimates built from the flow rates themselves, using a household of four as the baseline, and they assume no change in habits — just new fixtures doing the same jobs.
| Fixture swap | Saving per use | Typical household saving per year (estimated) |
|---|---|---|
| Toilet 3.5 to 1.28 gallons per flush | 2.22 gallons per flush | Around 13,000 gallons (EPA estimate for a WaterSense-labelled model) |
| Showerhead 2.5 to 1.8 gallons per minute | 7 gallons per 10-minute shower | Around 10,000 gallons for a family of four showering daily |
| Bathroom tap aerator 2.2 to 1.2 gallons per minute | 1 gallon per minute of running tap | 1,000 to 3,000 gallons depending on use |
| Kitchen tap aerator 2.2 to 1.5 gallons per minute | 0.7 gallons per minute of running tap | 700 to 2,000 gallons depending on use |
The dollar saving depends on your water agency's rates, and California rates vary widely — some agencies charge tiered rates where heavy use costs far more per gallon, which makes the saving bigger for high-use households. Check your last water bill for your per-unit rate and multiply it by the gallons above; that is your real number, not a national average. If your home also has a water softener or filtration system, note that efficient fixtures reduce the volume of water passing through it, which can extend the time between regeneration cycles.
Rebates: Check Before You Buy
Many California water agencies run rebate programmes for high-efficiency toilets and other water-saving fixtures, and the amounts are worth checking before you spend anything. In Southern California, the Metropolitan Water District's SoCal Water$mart programme has offered rebates on high-efficiency toilets, and many local agencies — including the Los Angeles Department of Water and Power and agencies across Orange County and the Inland Empire — run their own programmes on top of it. Northern California agencies, including the East Bay Municipal Utility District and the Santa Clara Valley Water District, have offered similar rebates at various times.
Two rules apply to almost every rebate programme. First, you usually need pre-approval before you buy — a receipt for a toilet you already installed will often not qualify. Second, the rebate typically requires a specific model from an approved list, usually a WaterSense-labelled toilet meeting a performance standard. Check your agency's website before you shop, and keep the receipt and the model number. The rebate will rarely cover the whole cost, but on a whole-house swap it can cover a meaningful share of it.
Choosing Fixtures That Last: A Checklist
Use this before you buy anything, and you will avoid the most common regrets:
- Verify the flow number stamped on the box or the unit, against the table at the top of this guide. Do not trust the marketing words on the front of the box.
- Look for the WaterSense label, which means the fixture has been independently tested for both efficiency and performance, not just flow.
- Buy brands your local supply house stocks, so cartridges, flappers and fill valves are available for years.
- Measure before ordering: rough-in for toilets, hole spacing and deck thickness for faucets, shower arm height for heads.
- Avoid the cheapest no-name import. It may meet the flow number on the day you buy it, but when a part fails in two years there will be no parts, no support and no choice but a full replacement.
- Keep the old fixture until the new one is tested. A toilet that rocks, a tap that drips from the base, or a showerhead that leaks at the joint are all easier to fix while the old fixture is still in the garage.
- Test everything before the installer leaves. Flush the toilet five times, run the shower for two minutes, and check every joint with a dry hand. A leak found on installation day is a five-minute fix; a leak found a month later is a call-back and a water stain.
If a fixture swap is part of a larger project — a remodel, a repipe, or a water-quality upgrade — it is worth coordinating the work so the walls are open once and the fixtures are chosen once. Our whole-home repiping page explains how fixture upgrades fit into a repipe project.
Frequently Asked Questions
Are water-efficient fixtures required in California?
Yes, for anything newly sold or installed. CalGreen and Title 20 set maximum flow rates: 1.28 gallons per flush for toilets, 1.8 gallons per minute for showerheads, 1.2 for bathroom faucets and 1.8 for kitchen faucets. Fixtures already installed do not have to be removed, but SB 407 requires homes built on or before 1 January 1994 to have non-compliant fixtures replaced, and any permitted alteration triggers replacement of all remaining non-compliant fixtures before final approval.
Do I have to replace old fixtures if I am not remodelling?
Under SB 407, homes built on or before 1 January 1994 were required to have non-compliant fixtures replaced by 1 January 2017, and sellers must disclose any that remain. In practice, if you are not selling and not pulling a permit, nobody will force the issue — but the fixtures are costing you water and money every day, and a toilet swap is one of the cheapest upgrades you can make.
Will a 1.28 gallon toilet actually flush properly?
A modern one, yes. Early low-flow toilets from the 1990s were poor, but current designs with a MaP rating of 600 grams or higher, a fully glazed trapway and a well-designed bowl clear waste reliably in a single flush. The reputation problem is thirty years out of date. Check the MaP rating rather than the price, and avoid the cheapest model in the shop.
Is a 1.8 gallon per minute showerhead too weak?
It does not have to be. Air-induction and pressure-compensating heads mix air into the stream and feel fuller than their flow rate suggests. What matters is the spray pattern and the nozzle design, not just the number. Try the head if you can, read reviews that mention water pressure specifically, and remember that hard water will clog fixed metal jets over time — silicone nozzles you can rub clean last longer.
Can I just fit an aerator instead of replacing the tap?
For water saving, yes — a 1.0 or 1.2 gallon-per-minute aerator on a bathroom tap achieves the same flow reduction as a new compliant faucet, for a few dollars and two minutes of work. But an aerator will not fix a worn cartridge, a dripping tap, a corroded body or a tap that is simply at the end of its life. If the tap works well and only the flow is too high, fit the aerator. If the tap drips or handles badly, replace it.
Do water-efficient fixtures save money on my water bill?
Yes, and the saving scales with your water rate. A household of four swapping old toilets can save around 13,000 gallons a year, and a showerhead swap can save around 10,000 gallons more. At tiered California rates, where heavy use costs more per gallon, high-use households save the most. Low-flow fixtures also save hot water, which cuts the energy bill too. Check your bill for your per-unit rate and multiply it by the gallons saved to get your real figure.
California's fixture rules are strict, but they are also straightforward: check the number, buy a fixture that meets it, and choose one that will still be working well in ten years. A well-chosen toilet, showerhead and set of aerators will save thousands of gallons a year, cut your water and energy bills, and keep you clear of the permit problems that catch pre-1994 homeowners by surprise. If you are planning a fixture upgrade or a remodel anywhere in California and want the work done properly the first time, California Plumbing Service can help you choose and install fixtures that meet the code and perform well for years. Call 719-403-0539 today.
Need a Plumber in California?
Written scope before work starts. One call connects you with a local plumbing team.